Leaders in
Hand Protection
and PPE

The ANSI/ISEA 105-2024 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

ESD is an acronym for electrostatic discharge. This discharge is the rapid transfer of static between two different objects. Although ESD doesn’t typically cause harm to the human body - you might only experience it as a small, surprising shock - it can cause extensive damage to electrical equipment and sensitive instruments. This damage may either be permanent, causing the device to malfunction (known as a catastrophic failure), or it may occur on a smaller scale that would be difficult to detect before the device is sent out for service (known as latent defect).

To see what chemicals included in the manufacturing of this product triggered the Prop 65 Warning please go to the Prop 65 Portal.

The ANSI/ISEA 105-2016 standard outlines test methods for contact heat and scored from 0-5. The ASTM F1060-18 test is used to test conductive heat resistance against gloves and PPE. Measuring the highest contact temperature for which the time to second-degree burn is at least 15 seconds and the alarm time is at least four seconds. Learn More

To see what chemicals included in the manufacturing of this product triggered the Prop 65 Warning please go to the Prop 65 Portal.

Class R3 apparel is intended for workers requiring the highest level of visibility, have high task loads and need to be visible throughout a full range of body motions.

We have a dedicated team that manages all of your logo requests and will help ensure the process runs smoothly from start to finish. If you have any questions along the way, they will be more than happy to assist you.

Experience the Difference

Class R3 apparel is intended for workers requiring the highest level of visibility, have high task loads and need to be visible throughout a full range of body motions.

Self Extinguishing garments are made from material that is not inherently flame retardant, but are chemically treated to become flame resistant. They are NOT designed for use in ARC flash or flash fire applications. When a flame source is removed from the treated material, the material will self-extinguish within a given time frame. The treated material can melt and drip and has a limited life span dependent on washings and what the garment is exposed to. Performance is established using the ASTM D6413 test method.

We have a dedicated team that manages all of your logo requests and will help ensure the process runs smoothly from start to finish. If you have any questions along the way, they will be more than happy to assist you.

Experience the Difference

We have a dedicated team that manages all of your logo requests and will help ensure the process runs smoothly from start to finish. If you have any questions along the way, they will be more than happy to assist you.

Experience the Difference

ESD is an acronym for electrostatic discharge. This discharge is the rapid transfer of static between two different objects. Although ESD doesn’t typically cause harm to the human body - you might only experience it as a small, surprising shock - it can cause extensive damage to electrical equipment and sensitive instruments. This damage may either be permanent, causing the device to malfunction (known as a catastrophic failure), or it may occur on a smaller scale that would be difficult to detect before the device is sent out for service (known as latent defect).

We have a dedicated team that manages all of your logo requests and will help ensure the process runs smoothly from start to finish. If you have any questions along the way, they will be more than happy to assist you.

Experience the Difference

To see what chemicals included in the manufacturing of this product triggered the Prop 65 Warning please go to the Prop 65 Portal.

We have a dedicated team that manages all of your logo requests and will help ensure the process runs smoothly from start to finish. If you have any questions along the way, they will be more than happy to assist you.

Experience the Difference

To see what chemicals included in the manufacturing of this product triggered the Prop 65 Warning please go to the Prop 65 Portal.

New edition ANSI/ISEA 105-2024 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

The ANSI/ISEA 105-2024 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3884-09 is used for uncoated gloves and the end point (failure) is the number of abrasion cycles when the first thread or yarn is broken. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher Abrasion Level.

We have a dedicated team that manages all of your logo requests and will help ensure the process runs smoothly from start to finish. If you have any questions along the way, they will be more than happy to assist you.

Experience the Difference

To see what chemicals included in the manufacturing of this product triggered the Prop 65 Warning please go to the Prop 65 Portal.

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

To attain the EN 374 pictogram shield gloves must pass at least a Level 2 in three chemicals. The chemicals listed above are the chemicals that passed for this glove.

We have a dedicated team that manages all of your logo requests and will help ensure the process runs smoothly from start to finish. If you have any questions along the way, they will be more than happy to assist you.

Experience the Difference

To see what chemicals included in the manufacturing of this product triggered the Prop 65 Warning please go to the Prop 65 Portal.

Class R3 apparel is intended for workers requiring the highest level of visibility, have high task loads and need to be visible throughout a full range of body motions.

We have a dedicated team that manages all of your logo requests and will help ensure the process runs smoothly from start to finish. If you have any questions along the way, they will be more than happy to assist you.

Experience the Difference

Type/Class R2 apparel is necessary for workers exposed to traffic traveling over 25 mph and who work against complex backgrounds.

Self Extinguishing garments are made from material that is not inherently flame retardant, but are chemically treated to become flame resistant. They are NOT designed for use in ARC flash or flash fire applications. When a flame source is removed from the treated material, the material will self-extinguish within a given time frame. The treated material can melt and drip and has a limited life span dependent on washings and what the garment is exposed to. Performance is established using the ASTM D6413 test method.

We have a dedicated team that manages all of your logo requests and will help ensure the process runs smoothly from start to finish. If you have any questions along the way, they will be more than happy to assist you.

Experience the Difference

To see what chemicals included in the manufacturing of this product triggered the Prop 65 Warning please go to the Prop 65 Portal.

The NFPA has identified the various FR hazardous risk category levels, which range from PPE 1 (which is low risk and requires AR clothing with a minimum arc rating of 4), up to PPE 4 (which is high risk and requires AR clothing with a minimum arc rating of 40). Each level, 1-4, is rated at a certain amount of flame resistance measured in cal/cm2.

New edition ANSI/ISEA 105-2024 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.

The ANSI/ISEA 105-2024 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3884-09 is used for uncoated gloves and the end point (failure) is the number of abrasion cycles when the first thread or yarn is broken. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher Abrasion Level.

The ANSI/ISEA 105-2024 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

The ANSI/ISEA 105-2016 standard outlines test methods for contact heat and scored from 0-5. The ASTM F1060-18 test is used to test conductive heat resistance against gloves and PPE. Measuring the highest contact temperature for which the time to second-degree burn is at least 15 seconds and the alarm time is at least four seconds. Learn More

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.

To attain the EN 374 pictogram shield gloves must pass at least a Level 2 in three chemicals. The chemicals listed above are the chemicals that passed for this glove.

New edition ANSI/ISEA 105-2024 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.